View AK5366VR_4122748.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ASAHI KASEI
[AK5366VR]
24-Bit 48kHz ADC with Selector/PGA/ALC
AK5366VR
GENERAL DESCRIPTION AK5366VR is a high-performance 24-bit, 48kHz sampling ADC for consumer audio and digital recording applications. Thanks to AKM's Enhanced Dual-Bit modulator architecture, this analog-to-digital converter has an impressive dynamic range of 103dB with a high level of integration. The AK5366VR has a 5-channel stereo input selector, an input Programmable Gain Amplifier with an ALC function. All this integration with high-performance makes the AK5366VR well suited for CD and DVD recording systems.
FEATURES 1. 24bit Stereo ADC * 5ch Stereo Inputs Selector * Input PGA from +18dB to 0dB, 0.5dB Step * Peak Hold Function * Auto Level Control (ALC) Circuit * Digital HPF for offset cancellation (fc=1.0Hz@fs=48kHz) * Digital Attenuator from +8dB to -63dB, Mute * Soft Mute * Single-end Inputs * S/(N+D) : 94dB * DR, S/N : 103dB * Audio I/F Format : 24bit MSB justified, I2S 2. 3-wire Serial P Interface / I2C-Bus 3. Master / Slave Mode 4. Master Clock : 256fs/384fs/512fs 5. Sampling Rate : 32kHz to 48kHz 6. Power Supply * AVDD: 4.75 5.25V (typ. 5.0V) * DVDD: 3.0 5.25V (typ. 3.3V) * TVDD: 3.0 5.25V for input tolerant (typ. 5.0V) 7. Ta = -40 85C 8. Package : 48pin LQFP (7mm x 7mm)
MS0526-E-00 -1-
2006/07
ASAHI KASEI
[AK5366VR]
Block Diagram
M/S LOPIN LIN1 LOUT IPGAL
SEL2 SEL1 SEL0
PDN
I2C
AVDD LIN2 LIN3 LIN4 LIN5 RIN1 RIN2 RIN3 RIN4 RIN5 Pre-Amp Pre-Amp IPGA (ALC) ADC Peak Hold HPF DATT Audio I/F Controller LRCK BICK MCLK SDTO TVDD IPGA (ALC) Control Register I/F VCOM AVSS DVDD DVSS
ROPIN
ROUT
IPGAR SMUTE CSN CCLK CDTI CAD1 SCL SDA
Block diagram
MS0526-E-00 -2-
2006/07
ASAHI KASEI
[AK5366VR]
Ordering Guide
AK5366VR AKD5366VR -40 +85C 48pin LQFP (0.5mm pitch) Evaluation Board for AK5366VR
Pin Layout
TEST8
TEST7
TEST6
TEST5
RIN5
RIN4
RIN3
RIN2
RIN1
M/S
LIN5 TEST1 LIN4 TEST2 LIN3 TEST3 LIN2 TEST4 LIN1 NC LOPIN LOUT
1 2 3 4 5 6 7 8 9
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
I2C
NC
CSN/CAD1 CCLK/SCL SDTI/SDA SEL2 SEL1 SEL0 SMUTE TVDD PDN MCLK LRCK BICK
AK5366VR Top View
32 31 30 29 28 27 26
10 11
25 12 13 14 15 16 17 18 19 20 21 22 23 24 IPGAR NC DVDD AVDD IPGAL ROUT ROPIN SDTO AVSS DVSS
MS0526-E-00 -3-
VCOM
NC
2006/07
ASAHI KASEI
[AK5366VR]
Compatibility with AK5365
AK5365 max. 96kHz "0" : ALC=OFF "7FH" : 0dB "89H" : +4.5dB 0dB +12dB -72dB 0dB No No 100kHz No 44pin LQFP AK5366 max. 48kHz "1" : ALC=ON "80H" : 0dB "8EH" : +7.0dB 0dB +18dB -63dB +8dB Yes Yes 400kHz Yes AK5366VR 48pin LQFP
fs ALC bit default value IPGL/R7-0 default value REF7-0 bit default value IPGA Gain DATT Volume MCLK AC Coupling Input Peak Hold Circuit I2C Speed 5V tolerant Package
Software Compatibility
Addr 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH Register Name Power Down & Reset Control Input Selector Control Clock & Format Control Timer Select Lch IPGA Control Rch IPGA Control ALC Mode Control 1 ALC Mode Control 2 Lch DATT Control Rch DATT Control Lch Peak Hold Low Byte Lch Peak Hold High Byte Rch Peak Hold Low Byte Rch Peak Hold High Byte D7 0 0 0 0 IPGL7 IPGR7 0 REF7 ATTL7 ATTR7 PHL7 PHL15 PHR7 PHR15 D6 0 0 0 0 IPGL6 IPGR6 0 REF6 ATTL6 ATTR6 PHL6 PHL14 PHR6 PHR14 D5 0 0 0 LTM1 IPGL5 IPGR5 ZELMN REF5 ATTL5 ATTR5 PHL5 PHL13 PHR5 PHR13 D4 0 0 0 LTM0 IPGL4 IPGR4 ALC REF4 ATTL7 ATTR4 PHL4 PHL12 PHR4 PHR12 D3 0 0 DIF ZTM1 IPGL3 IPGR3 FR REF3 ATTL7 ATTR3 PHL3 PHL11 PHR3 PHR11 D2 MCKPD SEL2 CKS1 ZTM0 IPGL2 IPGR2 LMTH REF2 ATTL7 ATTR2 PHL2 PHL10 PHR2 PHR10 D1 MCKAC SEL1 CKS0 WTM1 IPGL1 IPGR1 RATT REF1 ATTL7 ATTR1 PHL1 PHL9 PHR1 PHR9 D0 PWN SEL0 SMUTE WTM0 IPGL0 IPGR0 LMAT REF0 ATTL0 ATTR0 PHL0 PHL8 PHR0 PHR8
: Changing points from AK5365's register.
MS0526-E-00 -4-
2006/07
ASAHI KASEI
[AK5366VR]
PIN/FUNCTION
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Pin Name LIN5 TEST1 LIN4 TEST2 LIN3 TEST3 LIN2 TEST4 LIN1 NC LOPIN LOUT IPGAL NC IPGAR ROUT ROPIN NC AVDD AVSS VCOM DVSS DVDD SDTO I/O I I I I I I I I I I O I I O I O O Function Lch Analog Input 5 Pin Test 1 Pin This pin should be connected to AVSS. Lch Analog Input 4 Pin Test 2 Pin This pin should be connected to AVSS. Lch Analog Input 3 Pin Test 3 Pin This pin should be connected to AVSS. Lch Analog Input 2 Pin Test 4 Pin This pin should be connected to AVSS. Lch Analog Input 1 Pin No internal bonding. Connect to GND. Lch Feedback Resistor Input Pin Lch Feedback Resistor Output Pin Lch IPGA Input Pin No internal bonding. Connect to GND. Rch IPGA Input Pin Rch Feedback Resistor Output Pin Rch Feedback Resistor Input Pin No internal bonding. Connect to GND. Analog Power Supply Pin, 4.75 5.25V Analog Ground Pin Common Voltage Output Pin, AVDD/2 Bias voltage of ADC input. Digital Ground Pin Digital Power Supply Pin, 3.0 5.25V Audio Serial Data Output Pin
Note: All digital input pins except pull-down pins should not be left floating. Note: TEST1, TEST2, TEST3 and TEST4 pins should be connected to AVSS.
MS0526-E-00 -5-
2006/07
ASAHI KASEI
[AK5366VR]
No. 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
Pin Name BICK LRCK MCLK PDN TVDD SMUTE SEL0 SEL1 SEL2 CDTI SDA CCLK SCL CSN CAD1 I2C M/S NC RIN1 TEST5 RIN2 TEST6 RIN3 TEST7 RIN4 TEST8 RIN5
I/O I/O I/O I I I I I I I I/O I I I I I I I I I I I I I I I
Function Audio Serial Data Clock Pin Output Channel Clock Pin Master Clock Input Pin Power-Down Mode Pin "H": Power up, "L": Power down reset and initializes the control register. Input Buffer Power Supply Pin, 3.0 5.25V Soft Mute Pin (Internal Pull-down Pin, typ. 100k) "H" : Soft Mute, "L" : Normal Operation Input Selector 0 Pin Input Selector 1 Pin Input Selector 2 Pin Control Data Input Pin in 3-wire Control (I2C pin = "L") (I2C pin = "H") Control Data Input / Output Pin in I2C Control Control Data Clock Pin in 3-wire Control (I2C pin = "L") (I2C pin = "H") Control Data Clock Pin in I2C Control Chip Select Pin in 3-wire Control (I2C pin = "L") (I2C pin = "H") Chip Address 1 Select Pin in I2C Control Control Mode Pin "H" : I2C Control , "L" : 3-wire Control Master / Slave Mode Pin "H" : Master Mode, "L" : Slave Mode No internal bonding. Connect to GND. Rch Analog Input 1 Pin Test 5 Pin This pin should be connected to AVSS. Rch Analog Input 2 Pin Test 6 Pin This pin should be connected to AVSS. Rch Analog Input 3 Pin Test 7 Pin This pin should be connected to AVSS. Rch Analog Input 4 Pin Test 8 Pin This pin should be connected to AVSS. Rch Analog Input 5 Pin
Note: All digital input pins except pull-down pins should not be left floating. Note: TEST5, TEST6, TEST7 and TEST8 pins should be connected to AVSS.
MS0526-E-00 -6-
2006/07
ASAHI KASEI
[AK5366VR]
Handling of Unused Pin
The unused input pins should be processed appropriately as below. Classification Pin Name LIN1-5 RIN1-5 IPGAL IPGAR LOPIN/LOUT ROPIN/ROUT SMUTE SEL2-0 CSN CCLK/SCL CDTI/SDA I2C Setting These pins should be open. Connected 10k resistor between LOPIN pin and LOUT pin. Connected 10k resistor between ROPIN pin and ROUT pin.
Analog
Digital
These pins should be connected to DVSS.
MS0526-E-00 -7-
2006/07
ASAHI KASEI
[AK5366VR]
ABSOLUTE MAXIMUM RATINGS
(AVSS, DVSS=0V; Note 1 Parameter Power Supplies: Analog Digital Input Buffer (Note 2) |AVSS - DVSS| (Note 3) Input Current, Any Pin Except Supplies Analog Input Voltage (Note 4) (LIN1-5, RIN1-5, LOPIN, ROPIN, IPGAL, IPGAR, M/S pins) Digital Input Voltage 1 (MCLK, BICK, LRCK, PDN pins) Digital Input Voltage 2 (SMUTE, SEL2-0, CSN/CAD1, CCLK/SCL, CDTI/SDA, I2C pins) Ambient Temperature (Powered applied) Storage Temperature Symbol AVDD DVDD TVDD GND IIN VINA VIND1 VIND2 Ta Tstg min -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -40 -65 max 6.0 6.0 6.0 0.3 10 AVDD+0.3 DVDD+0.3 TVDD+0.3 85 150 Units V V V V mA V V V C C
Note 1. All voltages with respect to ground. Note 2. SMUTE, SEL2-0, CSN/CAD1, CCLK/SCL, CDTI/SDA and I2C pins correspond to 5V tolerant. Note 3. AVSS and DVSS must be connected to the same analog ground plane. Note 4. M/S pin is the digital input pin. However, M/S pin should be connected to AVDD or AVSS to prevent the noise to the analog input pins
WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes.
RECOMMENDED OPERATING CONDITIONS (AVSS, DVSS=0V; Note 1) Parameter Symbol min typ Analog AVDD 4.75 5.0 Power Supplies Digital DVDD 3.0 3.3 (Note 5) Input Buffer TVDD DVDD 5.0
Note 1. All voltages with respect to ground. Note 5. The power up sequence between AVDD, DVDD and TVDD is not critical.
max 5.25 AVDD AVDD
Units V V V
WARNING: AKM assumes no responsibility for the usage beyond the conditions in this datasheet.
MS0526-E-00 -8-
2006/07
ASAHI KASEI
[AK5366VR]
ANALOG CHARACTERISTICS (Ta=25C; AVDD=TVDD=5.0V, DVDD=3.3V; AVSS=DVSS=0V; fs=48kHz; BICK=64fs; Signal Frequency=1kHz; 24bit Data; Measurement frequency=20Hz 20kHz at fs=48kHz; unless otherwise specified) Parameter min typ max Units Pre-Amp Characteristics: Feedback Resistance 10 50 k S/(N+D) (Note 6) 100 dB S/N (A-weighted) (Note 6) 108 dB Load Resistance (Note 7) 6.3 k Load Capacitance 20 pF Input PGA Characteristics: Input Voltage (Note 8) 0.9 1 1.1 Vrms Input Resistance (Note 9) 6.3 10 15 k Step Size 0.2 0.5 0.8 dB Gain Control Range ALC = OFF 0 +18 dB ALC = ON -9.5 +18 dB ADC Analog Input Characteristics: IPGA=0dB, ALC = OFF (Note 10) Resolution 24 Bits S/(N+D) (-0.5dBFS) 84 94 dB DR (-60dBFS, A-weighted) 96 103 dB S/N (A-weighted) 96 103 dB Interchannel Isolation (Note 11) 90 110 dB Interchannel Gain Mismatch 0.2 0.5 dB Gain Drift 100 ppm/C Power Supply Rejection (Note 12) 50 dB Power Supplies Power Supply Current Normal Operation (PDN pin = "H") mA 35 23 AVDD mA 8 4 DVDD+TVDD Power-down mode (PDN pin = "L") (Note 13) A 100 10 AVDD A 100 10 DVDD+TVDD
Note 6. This value is measured at LOUT and ROUT pins using the circuit as shown in Figure 25. The input signal voltage is 2Vrms. Note 7. This value is the input impedance of an external device that the LOUT and ROUT pins can drive, when a device is connected with LOUT and ROUT pin externally. The feedback resistor (min. 10k) that it is usually connected with the LOUT/ROUT pins, and the value of input impedance (min. 6.3k) of the IPGAL/R pins are not included. Note 8. Full scale (0dB) of the input voltage at ALC=OFF and IPGA=0dB. Input voltage to IPGAL and IPGAR pins is proportional to AVDD voltage. typ. Vin = 0.2 x AVDD (Vrms). Note 9. This value is input impedance of the IPGAL and IPGAR pins. Note 10. This value is measured via the following path. Pre-Amp IPGA (Gain : 0dB) ADC. The measurement circuit is Figure 25. Note 11. This value is the interchannel isolation between all the channels of the LIN1-5 and RIN1-5 when the applied input signal causes the Pre-Amp output to equal IPGA input. Note 12. PSR is applied to AVDD, DVDD and TVDD with 1kHz, 50mVpp. Note 13. All digital input pins are held DVSS.
MS0526-E-00 -9-
2006/07
ASAHI KASEI
[AK5366VR]
FILTER CHARACTERISTICS (Ta=-40 85C; AVDD=4.75 5.25V; DVDD, TVDD=3.0 5.25V; fs=48kHz) Parameter Symbol min typ ADC Digital Filter (Decimation LPF): Passband (Note 14) -0.005dB PB 0 -0.02dB 21.768 -0.06dB 22.0 -6.0dB 24.0 Stopband SB 26.5 Passband Ripple PR Stopband Attenuation SA 80 Group Delay (Note 15) GD 31 Group Delay Distortion GD 0 ADC Digital Filter (HPF): Frequency Response (Note 14) -3dB FR 1.0 -0.5dB 2.9 -0.1dB 6.5
max 21.5 0.005
Units kHz kHz kHz kHz kHz dB dB 1/fs s Hz Hz Hz
Note 14. The passband and stopband frequencies scale with fs. For example, 21.768kHz at -0.02dB is 0.454 x fs. Note 15. The calculated delay time induced by digital filtering. This time is from the input of an analog signal to the setting of 24bit data both channels to the ADC output register for ADC.
DC CHARACTERISTICS (Ta=-40 85C; AVDD=4.75 5.25V; DVDD, TVDD=3.0 5.25V) Parameter Symbol min High-Level Input Voltage (Note 16) VIH 70%DVDD Low-Level Input Voltage (Note 16) VIL Input Voltage at AC Coupling (Note 17) VAC 50%DVDD High-Level Output Voltage (Iout=-400A) VOH DVDD-0.5 Low-Level Output Voltage (Except SDA pin : Iout=400A) VOL (SDA pin : Iout=3mA) VOL Input Leakage Current (Note 18) Iin -
typ -
max 30%DVDD 0.5 0.4 10
Units V V V V V V A
Note 16. SMUTE, SEL2-0, CSN/CAD1, CCLK/SCL, CDTI/SDA and I2C pins correspond to 5V tolerant. Note 17. When AC coupled capacitor is connected to MCLK pin. Note 18. SMUTE pin is internally connected to a pull-down resistor. (typ. 100k)
MS0526-E-00 - 10 -
2006/07
ASAHI KASEI
[AK5366VR]
SWITCHING CHARACTERISTICS (Ta=-40 85C; AVDD=4.75 5.25V; DVDD, TVDD=3.0 5.25V; CL=20pF) Parameter Symbol min Master Clock Timing Frequency fCLK 8.192 Pulse Width Low tCLKL 0.3/fCLK Pulse Width High tCLKH 0.3/fCLK AC Pulse Width (Note 19) tACW 0.4/fCLK LRCK Frequency Frequency fsn 32 Duty Cycle Slave mode 45 Master mode Audio Interface Timing Slave mode 160 tBCK BICK Period 65 tBCKL BICK Pulse Width Low 65 tBCKH Pulse Width High 30 tLRB LRCK Edge to BICK "" (Note 20) 30 tBLR BICK "" to LRCK Edge (Note 20) 2 tLRS LRCK to SDTO (MSB) (Except I S mode) tBSD BICK "" to SDTO Master mode BICK Frequency fBCK BICK Duty dBCK BICK "" to LRCK tMBLR -20 BICK "" to SDTO tBSD -20
typ
max 24.576
Units MHz ns ns ns kHz % %
48 55 50
35 35 64fs 50 20 35
ns ns ns ns ns ns ns Hz % ns ns
Note 19. Pulse width to ground level when MCLK is connected to a capacitor in series and a resistor is connected to ground. Note 20. BICK rising edge must not occur at the same time as LRCK edge.
MS0526-E-00 - 11 -
2006/07
ASAHI KASEI
[AK5366VR]
Parameter Control Interface Timing (3-wire Serial mode): CCLK Period CCLK Pulse Width Low Pulse Width High CDTI Setup Time CDTI Hold Time CSN "H" Time CSN "" to CCLK "" CCLK "" to CSN "" Control Interface Timing (I2C Bus mode): SCL Clock Frequency Bus Free Time Between Transmissions Start Condition Hold Time (prior to first clock pulse) Clock Low Time Clock High Time Setup Time for Repeated Start Condition SDA Hold Time from SCL Falling (Note 21) SDA Setup Time from SCL Rising Rise Time of Both SDA and SCL Lines Fall Time of Both SDA and SCL Lines Setup Time for Stop Condition Pulse Width of Spike Noise Suppressed by Input Filter Reset Timing PDN Pulse Width PDN "" to SDTO valid CSN "" to SDTO valid (Note 22) (Note 23) (Note 24)
Symbol tCCK tCCKL tCCKH tCDS tCDH tCSW tCSS tCSH fSCL tBUF tHD:STA tLOW tHIGH tSU:STA tHD:DAT tSU:DAT tR tF tSU:STO tSP tPD tPDV tPDV
min 200 80 80 40 40 150 50 50 1.3 0.6 1.3 0.6 0.6 0 0.1 0.6 0 150
typ
max
Units ns ns ns ns ns ns ns ns
400 0.3 0.3 50
kHz s s s s s s s s s s ns ns 1/fs 1/fs
516 516
Note 21. Data must be held long enough to bridge the 300ns-transition time of SCL. Note 22. The AK5366VR can be reset by bringing the PDN pin = "L". Note 23. This cycle is the number of LRCK rising edges from the PDN pin = "H". Note 24. This cycle is the number of LRCK rising edges from the CSN = "H".
Purchase of Asahi Kasei Microsystems Co., Ltd I2C components conveys a license under the Philips I2C patent to use the components in the I2C system, provided the system conform to the I2C specifications defined by Philips.
MS0526-E-00 - 12 -
2006/07
ASAHI KASEI
[AK5366VR]
Timing Diagram
1/fCLK VIH MCLK VIL tCLKH 1/fs VIH LRCK VIL tBCK VIH BICK VIL tBCKH tBCKL
Clock Timing
1/fCLK
tCLKL
1000pF MCLK Input 100k AGND Measurement Point AGND
tACW
tACW
VAC
MCLK AC Coupling Timing (Measurement condition) *Refer to Figure 2 for input circuit example.
MS0526-E-00 - 13 -
2006/07
ASAHI KASEI
[AK5366VR]
VIH LRCK VIL tBLR tLRB VIH BICK VIL tLRS tBSD
SDTO
50%DVDD
Audio Interface Timing (Slave mode)
LRCK
50%DVDD
tMBLR
dBCK 50%DVDD
BICK
tBSD
SDTO
50%DVDD
Audio Interface Timing (Master mode)
VIH CSN VIL tCSS tCCKL tCCKH VIH CCLK VIL tCDS CDTI C1 C0 tCDH VIH R/W VIL
WRITE Command Input Timing
MS0526-E-00 - 14 -
2006/07
ASAHI KASEI
[AK5366VR]
tCSW VIH CSN VIL tCSH VIH CCLK VIL
VIH CDTI D2 D1 D0 VIL
WRITE Data Input Timing
SDA
tBUF tLOW tR tHIGH tF tSP
VIH VIL
VIH SCL VIL
tHD:STA Stop Start tHD:DAT tSU:DAT tSU:STA Start tSU:STO Stop
I C Bus Mode Timing
VIH CSN VIL tPDV
2
SDTO
50%DVDD
VIH PDN VIL tPDV
SDTO tPD PDN
50%DVDD
VIL
Power Down & Reset Timing
MS0526-E-00 - 15 -
2006/07
ASAHI KASEI
[AK5366VR]
OPERATION OVERVIEW System Clock
MCLK (256fs/384fs/512fs), BICK (48fs) and LRCK (fs) clocks are required in slave mode. The LRCK clock input must be synchronized with MCLK, however the phase is not critical. MCLK frequency is automatically detected in slave mode. Table 1 shows the relationship of typical sampling frequency and the system clock frequency. Setting of CKS 1-0 bit is ignored. MCLK (256fs/384fs/512fs) is required in master mode. MCLK frequency is selected by CKS1-0 bits as shown in Table 2. In master mode, after setting CKS1-0 bits, there is a possibility the frequency and duty of LRCK and BICK outputs become an abnormal state. All external clocks (MCLK, BICK and LRCK) must be present unless PDN pin = "L" and PWN bit = "1". If these clocks are not provided, the AK5366VR may draw excess current due to its use of internal dynamically refreshed logic. If the external clocks are not present, place the AK5366VR in power-down mode (PDN pin = "L" or PWN bit = "0"). In master mode, the master clock (MCLK) must be provided unless PDN pin = "L". fs 32kHz 44.1kHz 48kHz MCLK 256fs 384fs 512fs 8.192MHz 12.288MHz 16.384MHz 11.2896MHz 16.9344MHz 22.5792MHz 12.288MHz 18.432MHz 24.576MHz Table 1. System clock example (Slave mode)
CKS1 CKS0 MCLK 0 0 256fs Default 0 1 512fs 1 0 384fs 1 1 N/A Table 2. Master clock frequency select (Master mode)
MS0526-E-00 - 16 -
2006/07
ASAHI KASEI
[AK5366VR]
[MCLK AC Coupling input] MCLK AC coupling input becomes possible by controlling MCKPD bit and MCKAC bit. Master Clock External Clock Direct Input Status MCKAC bit Clock is input to MCLK pin. 0 Clock isn't input to MCLK pin. 0 AC Coupling Input (Figure 2) Clock is input to MCLK pin. 1 Clock isn't input to MCLK pin. 1 Table 3. MCKPD bit and MCKAC bit setting for Master Clock Status (Figure 1) (1) External clock direct input MCKPD bit 0 Don't care 0 1
MCLK
External Clock
MCKAC = "0" MCKPD = "0"
AK5366VR
Figure 1. External Master Clock Input Block
(2) AC coupling input
C External Clock
MCLK
MCKAC = "1" MCKPD = "0"
AK5366VR
Figure 2. External Clock mode (Input : 50%DVDD, Input circuit example) - Note: This clock level must not exceed DVDD level. (C : 0.1F)
Audio Interface Format
Two kinds of data formats can be chosen with the DIF bit (Table 4). In both modes, the serial data is in MSB first, 2's compliment format. The SDTO is clocked out on the falling edge of BICK. The audio interface supports both master and slave modes. In master mode, BICK and LRCK are output with the BICK frequency fixed to 64fs and the LRCK frequency fixed to 1fs. Mode 0 1 DIF bit 0 1 BICK 48fs (Slave) 24bit, MSB justified H/L 64fs (Master) 48fs (Slave) 2 24bit, I S Compatible L/H 64fs (Master) Table 4. Audio Interface Format SDTO LRCK Figure Figure 3 Figure 4 Default
MS0526-E-00 - 17 -
2006/07
ASAHI KASEI
[AK5366VR]
LRCK
012 20 21 22 23 24 31 0 1 2 20 21 22 23 24 31 0 1
BICK(64fs) SDTO(o)
23 22 43210 23 22 43210 23
23:MSB, 0:LSB Lch Data Rch Data
Figure 3. Mode 0 Timing
LRCK
0123 21 22 23 24 25 012 21 22 23 24 25 01
BICK(64fs) SDTO(o)
23 22 43210 23 22 43210
23:MSB, 0:LSB Lch Data Rch Data
Figure 4. Mode 1 Timing
Master Mode and Slave Mode
The M/S pin selects either master or slave mode. M/S pin = "H" selects master mode and "L" selects slave mode. The AK5366VR outputs BICK and LRCK in master mode. In slave mode, MCLK, BICK and LRCK are input externally. BICK, LRCK BICK = Input Slave Mode LRCK = Input BICK = Output Master Mode LRCK = Output Table 5. Master mode/Slave mode
Digital High Pass Filter
The ADC has a digital high pass filter for DC offset cancellation. The cut-off frequency of the HPF is 1.0Hz (@fs=48kHz) and scales with sampling rate (fs).
MS0526-E-00 - 18 -
2006/07
ASAHI KASEI
[AK5366VR]
Power-up/down
The AK5366VR is placed in the power-down mode by bringing PDN pin = "L" and the digital filter is also reset at the same time. This reset should always be done after power-up. An analog initialization cycle starts after exiting the power-down mode. Therefore, the output data SDTO becomes available after 516 cycles of LRCK.
Power Supply PDN pin ADC Internal State ALC bit ALC Function 150ns
PDN
INITA "1" ON Unknown "0"
Normal "0" OFF (1) Output
IPGA SDTO External clocks in slave mode External clocks in master mode BICK, LRCK in master mode Fixed to "L"
MCLK, BICK, LRCK Input The clocks can be stopped. MCLK Input BICK, LRCK Output
* PDN : Power down state. * INITA : Initializing period of ADC analog section (516/fs). * (1) : After ALC operation is disabled, the IPGA changes to the last written data during or before ALC operation. Figure 5. Power-up Sequence
Peak Hold Circuit
The AK5366VR includes the peak hold circuit. The peak is held L/R audio data independently. These registers are reset by reading 8bit of MSB, reading 8bit of both MSB and LSB should be continuity controlled by reading in order of 8bit of MSB from LSB. After reading 8bit of LSB the last, 8bit of MSB is lost by reading 8bit of LSB the last. The output value is the absolute value. Full scale is "FFFFH".
MS0526-E-00 - 19 -
2006/07
ASAHI KASEI
[AK5366VR]
Input Selector
The AK5366VR includes 5ch stereo input selectors (Figure 6). The input selector is 5 to 1 selector. The input channel is set by the SEL2-0 bits (Table 6) and the SEL2-0 pins (Table 7). The SEL2-0 pins should be fixed to "LLL" if the AK5366VR is controlled by the SEL 2-0 bits, because the setting of the SEL2-0 pins are prior to the SEL2-0 bits setting. SEL2 bit 0 0 0 0 1 SEL1 bit SEL0 bit Input Channel 0 0 LIN1 / RIN1 0 1 LIN2 / RIN2 1 0 LIN3 / RIN3 1 1 LIN4 / RIN4 0 0 LIN5 / RIN5 Table 6. Input Selector (SEL2-0 pin = "LLL") SEL1 pin SEL0 pin Input Channel L L LIN1 / RIN1 L H LIN2 / RIN2 H L LIN3 / RIN3 H H LIN4 / RIN4 L L LIN5 / RIN5 Table 7. Input Selector (SEL2-0 bit = "000")
Default
SEL2 pin L L L L H
LIN1 LIN2 LIN3 LIN4 LIN5 RIN1 RIN2 RIN3 RIN4 RIN5 Pre-Amp Pre-Amp
Figure 6. Input Selector
MS0526-E-00 - 20 -
2006/07
ASAHI KASEI
[AK5366VR]
[Input selector switching sequence] The input selector should be changed after soft mute to avoid the switching noise of the input selector (Figure 7). 1. Enable the soft mute before changing channel. 2. Change channel. 3. Disable the soft mute.
SMUTE (1) (2) (1)
D AT T Level A ttenuation
-
C hannel LIN 1/R IN 1 LIN 2/R IN 2
Figure 7. Input channel switching sequence example
The period of (1) varies in the setting value of DATT. It takes 1028/fs to mute when DATT value is +8dB. When changing channels, the input channel should be changed during (2). The period of (2) should be around 200ms because there is some DC difference between the channels.
MS0526-E-00 - 21 -
2006/07
ASAHI KASEI
[AK5366VR]
Input Attenuator
The input ATTs are constructed by adding the input resistor (Ri) for LIN1-5/RIN1-5 pins and the feedback resistor (Rf) between LOPIN (ROPIN) pin and LOUT (ROUT) pin (Figure 8). The input voltage range of the IPGAL/IPGAR pin is typically typ. 0.2 x AVDD (Vrms). If the input voltage of the input selector exceeds typ. 0.2 x AVDD, the input voltage of the IPGAL/IPGAR pins must be attenuated to 0.2 x AVDD by the input ATTs. Table 8 shows the example of Ri and Rf.
Rf LOPIN Ri Ri Ri Ri Ri Ri Ri Ri Ri Ri LIN1 LIN2 LIN3 To IPGA LIN4 LIN5 RIN1 RIN2 RIN3 RIN4 RIN5 Pre-Amp To IPGA Pre-Amp LOUT IPGAL
ROPIN
ROUT Rf
IPGAR
Figure 8. Input ATT * Example for input range Input Range 4Vrms 2Vrms 1Vrms Ri [k] 47 47 47 ATT Gain [dB] Rf [k] 12 -11.86 24 -5.84 47 0 Table 8. Input ATT example IPGAL/R pin 1.02Vrms 1.02Vrms 1Vrms
MS0526-E-00 - 22 -
2006/07
ASAHI KASEI
[AK5366VR]
Input Volume
The AK5366VR includes two independent channel analog volumes (IPGA) with 37 levels at 0.5dB steps located in front of the ADC. The IPGA is a true analog volume control that improves the S/N ratio as seen in Table 9. Independent zero-crossing detection is used to ensure level changes only occur during zero-crossings. If there are no zero-crossings, the level will then change after a time-out period (Table 10); the time-out period scales with fs. If a new value is written to the IPGA register before the IPGA changes at the zero crossing or time-out, the previous value becomes invalid. The timer (channel independent) for time-out is reset and the timer restarts for new IPGA value. Input Gain Setting 0dB +6dB fs=48kHz, A-weight 103dB 100dB Table 9. PGA+ADC S/N ZTM1 0 0 1 1 ZTM0 0 1 0 1
+18dB 89dB
Zero crossing timeout period @fs=48kHz 288/fs 6ms 1152/fs 24ms 2304/fs 48ms 4608/fs 96ms Table 10. Zero crossing timeout period
Default
[Writing operation at ALC Enable] Writing to the area over 7FH (Table 17) of IPGL/R registers (04H, 05H) is ignored during ALC operation. After ALC is disabled, the IPGA changes to the last written data by zero-crossing or time-out. In case of writing to the DATT area (08H, 09H), the DATT changes even if ALC is enabled.
Output Volume
The AK5366VR includes two independent channel digital volumes (DATT) with 144 levels at 0.5dB steps located behind the ADC. When changing levels, transitions are executed via soft changes; thus no switching noise occurs during these transitions. The data must not be written over 90H. ATTL/R7-0 Attenuation 8FH +8.0dB 8EH +7.5dB : : 81H +1.0dB 80H +0.5dB 7FH 0dB Default 7EH -0.5dB 7DH -1.0dB : : 02H -62.5dB 01H -63dB 00H Mute (-) Table 11. DATT Code Table
MS0526-E-00 - 23 -
2006/07
ASAHI KASEI
[AK5366VR]
ALC Operation
[1] ALC Limiter Operation When the ALC limiter is enabled, and either Lch or Rch exceed the ALC limiter detection level (LMTH bit), the IPGA value is attenuated by the amount defined in the ALC limiter ATT step (LMAT bit) automatically. Then the IPGA value is changed commonly for L/R channels. When the ZELMN bit = "1", the timeout period is set by the LTM1-0 bits. The operation for attenuation is done continuously until the input signal level becomes the ALC limiter detection level (LMTH bit) or less. If the ALC bit does not change into "0" or the ALC pin does not change into "L" after completing the attenuation, the attenuation operation repeats until the input signal level equals or exceeds the ALC limiter detection level (LMTH bit). When the ZELMN bit = "0", the timeout period is set by the ZTM1-0 bits. This enables the zero-crossing attenuation function so that the IPGA value is attenuated at the zero-detect points of the waveform. When FR bit = "1", the ALC operation corresponds to the impulse noise in additional to the normal ALC operation. Then if the impulse noise is supplied at ZELMN bit = "0", the ALC operation becomes the faster period than a set of ZTM1-0 bits. In case of ZELMN bit = "1", it becomes the same period as LTM1-0 bits. When FR bit = "0", the ALC operation is the normal ALC operation. [2] ALC Recovery Operation The ALC recovery refers to the amount of time that the AK5366VR will allow a signal to exceed a predetermined limiting value prior to enabling the limiting function. The ALC recovery operation uses the WTM1-0 bits to define the wait period used after completing an ALC limiter operation. If the input signal does not exceed the "ALC Recovery Waiting Counter Reset Level", the ALC recovery operation starts. The IPGA value increases automatically during this operation up to the reference level (REF7-0 bits). The ALC recovery operation is done at a period set by the WTM1-0 bits. Zero crossing is detected during WTM1-0, the ALC recovery operation waits WTM1-0 period and the next recovery operation starts. During the ALC recovery operation, when input signal level exceeds the ALC limiter detection level (LMTH bit), the ALC recovery operation changes immediately into an ALC limiter operation. In the case of "(Recovery waiting counter reset level) Input Signal < Limiter detection level" during the ALC recovery operation, the wait timer for the ALC recovery operation is reset. Therefore, in the case of "(Recovery waiting counter reset level) > Input Signal", the wait timer for the ALC recovery operation starts. When the impulse noise is input at FR bit = "1", the ALC recovery operation becomes faster than a normal recovery operation. When the FR bit = "0", the ALC recovery operation is done by normal period.
MS0526-E-00 - 24 -
2006/07
ASAHI KASEI
[AK5366VR]
[3] ALC Level Diagram (1) ALC=OFF Figure 9 and 10 show the level diagram example at ALC=OFF. In Figure 9, Input ATT is -12dB.
Input 4Vrms -12dB 2Vrms -12dB 1Vrms +6dB -12dB +12dB 0dBFS ATT -12dB IPGA ADC
Figure 9. ALC Level diagram example (ALC=OFF) In Figure 10, Input ATT is -6dB.
Input 2Vrms -6dB 1Vrms -6dB 0.5Vrms -6dB +12dB +6dB 0dBFS ATT -6dB IPGA ADC
Figure 10. ALC Level diagram example (ALC=OFF)
MS0526-E-00 - 25 -
2006/07
ASAHI KASEI
[AK5366VR]
(2) ALC=ON Figure 11 and 12 show the level diagram example at ALC=ON. In Figure 11, Input ATT is -12dB and REF7-0 bits are "8CH".
Input 4Vrms -12dB 2Vrms -12dB 1Vrms -0.5dB +5.5dB 0.5Vrms -12dB 0.25Vrms +6dB -12dBFS -6dBFS 0dBFS -0.5dBFS ATT -12dB ALC ADC
Figure 11. ALC Level diagram example (ALC=ON, LMTH bit="0") In Figure 12, Input ATT is -6dB and REF7-0 bits are "8CH".
Input 2Vrms -6dB 1Vrms -0.5dB -6dB 0.5Vrms -6dB 0.25Vrms +6dB -12dBFS +5.5dB -6dBFS 0dBFS -0.5dBFS ATT -6dB ALC ADC
Figure 12. ALC Level diagram example (ALC=ON, LMTH="0")
MS0526-E-00 - 26 -
2006/07
ASAHI KASEI
[AK5366VR]
[4] Example of ALC Operation The following registers should not be changed during the ALC operation. * LTM1-0, LMTH, LMAT, WTM1-0, ZTM1-0, RATT, REF7-0, ZELMN bits * The IPGA value of Lch becomes the start value if the IPGA value is different with Lch and Rch when the ALC starts. * Writing to the area over 80H (Table 17) of IPGL/R registers (04H, 05H) is ignored during ALC operation. After ALC is disabled, the IPGA changes to the last written data by zero-crossing or time-out. In case of writing to the DATT area (Table 11) of DATT registers (08H, 09H), the DATT changes even if ALC is enabled.
PDN = "L" "H"
ALC Operation
ALC OFF (WR: ALC = "0")
Manual Mode
Set (SEL2-0 bits or SEL2-0 pins)
WR (ZTM1-0, WTM1-0, LTM1-0)
WR (LMAT, RATT, LMTH)
WR (REF7-0)
WR (IPGA7-0)
(1)
WR (ALC = "1")
(2)
ALC Operation
No
Finish ALC mode?
(1)
Yes WR (ALC = "0")
(2)
Finish ALC mode and return to manual mode
Note : WR : Write Figure 13. Registers set-up sequence at ALC operation (1): Enable soft mute (2): Disable soft mute
Note : After ALC operation is disabled, the IPGA changes to the last written data during or before ALC operation.
MS0526-E-00 - 27 -
2006/07
ASAHI KASEI
[AK5366VR]
[5] IPGA value before and after ALC operation After ALC operation is disabled, the IPGA changes to the last written data during or before ALC operation. [Operation Example 1] 1. Set IPGA = +12dB at ALC=OFF. DATT portion is set to 0dB internally. 2. ALC=ON after soft mute is enabled. 3. Disable the soft mute. 4. During ALC operation. The IPGA changes from -9.5dB to the value set by REF7-0 bits. 5. ALC=OFF after soft mute is enabled. 6. Disable the soft mute. The IPGA return to +12dB automatically. [Operation Example 2] 1. Set IPGA = +12dB at ALC=OFF. DATT portion is set to 0dB internally. 2. ALC=ON after soft mute is enabled. 3. Disable the soft mute. 4. During ALC operation. When the DATT portion is set to -10dB, the IPGA changes from -19.5dB to the value set by REF7-0 bits. 5. ALC=OFF after soft mute is enabled. 6. Disable the soft mute. The IPGA setting is -10dB.
Soft Mute Operation
Soft mute operation is performed in the digital domain of the ADC output. Soft mute can be controlled by SMUTE bit or SMUTE pin. The SMUTE bit and SMUTE pin are ORed between pin and register. When SMUTE bit goes "1" or SMUTE pin goes "H", the ADC output data is attenuated by - within 1028 LRCK cycles. When the SMUTE bit returned "0" and SMUTE pin goes "L" the mute is cancelled and the output attenuation gradually changes to DATT value within 1028 LRCK cycles. If the soft mute is cancelled before mute state after starting of the operation, the attenuation is discontinued and returned to DATT value. Soft mute function and digital volume are common.
SMUTE (1) (3)
D AT T Level A ttenuation
-
GD (2) SDTO GD
Figure 14. Soft Mute Function (1) The output signal is attenuated by - within 1028 LRCK cycles (1028/fs). (2) Digital output delay from the analog input is called the group delay (GD). (3) If the soft mute is cancelled before the mute, the attenuation is discontinued and returned to DATT value.
MS0526-E-00 - 28 -
2006/07
ASAHI KASEI
[AK5366VR]
Chip Address
In case of 3-wire control mode, the chip address is fixed to C1 bit = "1" and C0 bit = "0". Table 12 shows the relationship between chip address (C1-0 bits) and CAD1 pin in I2C-bus control mode. CAD1 pin C1 bit C0 bit L 0 Fixed to "1" H 1 Fixed to "1" 2 Table 12. Chip address in I C-bus control Note : C1 bit should match with the input level of CAD1 pin.
Serial Control Interface
(1) 3-wire Serial Control Mode (I2C pin = "L") Internal registers may be written by using the 3-wire P interface pins (CSN, CCLK and CDTI). The data on this interface consists of a Chip address (2bits, Fixed to "10"), Read/Write (1bit, Fixed to "1", Write only), Register address (MSB first, 5bits) and Control data (MSB first, 8bits). Address and data is clocked in on the rising edge of CCLK and data is clocked out on the falling edge. After a low-to-high transition of CSN, data is latched for write operations. The clock speed of CCLK is 5MHz (max). The value of internal registers is initialized at PDN pin = "L".
CSN 0 CCLK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
CDTI
C1
C0
R/W
A4
A3
A2
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
C1 - C0 : Chip Address (C1="1", C0="0") R/W : READ / WRITE (Fixed to "1" : WRITE only) A4 - A0 : Register Address D7 - D0 : Control Data
Figure 15. Serial Control I/F Timing
MS0526-E-00 - 29 -
2006/07
ASAHI KASEI
[AK5366VR]
(2) I2C-bus Control Mode (CTRL pin = "H") The AK5366VR supports the standard-mode and the first-mode I2C-bus system (max: 400kHz). (2)-1. WRITE Operations Figure 16 shows the data transfer sequence for the I2C-bus mode. All commands are preceded by a START condition. A HIGH to LOW transition on the SDA line while SCL is HIGH indicates a START condition (Figure 22). After the START condition, a slave address is sent. This address is 7 bits long followed by an eighth bit that is a data direction bit (R/W). The most significant five bits of the slave address are fixed as "00100". The next one bit are CAD1 (device address bits). This one bit identify the specific device on the bus. The hard-wired input pin (CAD1 pin) set these device address bits (Figure 17). If the slave address matches that of the AK5366VR, the AK5366VR generates an acknowledge and the operation is executed. The master must generate the acknowledge-related clock pulse and release the SDA line (HIGH) during the acknowledge clock pulse (Figure 23). A R/W bit value of "1" indicates that the read operation is to be executed. A "0" indicates that the write operation is to be executed. The second byte consists of the control register address of the AK5366VR. The format is MSB first, and those most significant 3-bits are fixed to zeros (Figure 18). The data after the second byte contains control data. The format is MSB first, 8bits (Figure 19). The AK5366VR generates an acknowledge after each byte has been received. A data transfer is always terminated by a STOP condition generated by the master. A LOW to HIGH transition on the SDA line while SCL is HIGH defines a STOP condition (Figure 22). The AK5366VR can perform more than one byte write operation per sequence. After receipt of the third byte the AK5366VR generates an acknowledge and awaits the next data. The master can transmit more than one byte instead of terminating the write cycle after the first data byte is transferred. After receiving each data packet the internal 5-bit address counter is incremented by one, and the next data is automatically taken into the next address. If the address exceeds 0DH prior to generating the stop condition, the address counter will "roll over" to 00H and the previous data will be overwritten. The data on the SDA line must remain stable during the HIGH period of the clock. The HIGH or LOW state of the data line can only change when the clock signal on the SCL line is LOW (Figure 24) except for the START and STOP conditions.
S T A R T
R/W="0"
S T O P Sub Address(n) Data(n) A C K A C K Data(n+1) A C K A C K Data(n+x) A C K P
SDA
Slave S Address A C K
Figure 16. Data Transfer Sequence at the I2C-Bus Mode
0
0
1
0
0
CAD1
1
R/W
(CAD1 should match with CAD1 pin.) Figure 17. The First Byte
0
0
0
A4
A3
A2
A1
A0
Figure 18. The Second Byte
D7
D6
D5
D4
D3
D2
D1
D0
Figure 19. Byte Structure after the second byte
MS0526-E-00 - 30 -
2006/07
ASAHI KASEI
[AK5366VR]
(2)-2. READ Operations Set the R/W bit = "1" for the READ operation of the AK5366VR. After transmission of data, the master can read the next address's data by generating an acknowledge instead of terminating the write cycle after the receipt of the first data word. After receiving each data packet the internal 5-bit address counter is incremented by one, and the next data is automatically taken into the next address. If the address exceeds 0DH prior to generating a stop condition, the address counter will "roll over" to 00H and the previous data will be overwritten. The AK5366VR supports two basic read operations: CURRENT ADDRESS READ and RANDOM ADDRESS READ. (2)-2-1. CURRENT ADDRESS READ The AK5366VR contains an internal address counter that maintains the address of the last word accessed, incremented by one. Therefore, if the last access (either a read or write) were to address n, the next CURRENT READ operation would access data from the address n+1. After receipt of the slave address with R/W bit set to "1", the AK5366VR generates an acknowledge, transmits 1-byte of data to the address set by the internal address counter and increments the internal address counter by 1. If the master does not generate an acknowledge to the data but instead generates a stop condition, the AK5366VR ceases transmission.
S T A R T
R/W="1"
S T O P Data(n) Data(n+1) A C K A C K Data(n+2) A C K A C K Data(n+x) A C K P
SDA
Slave S Address A C K
Figure 20. CURRENT ADDRESS READ (2)-2-2. RANDOM ADDRESS READ The random read operation allows the master to access any memory location at random. Prior to issuing the slave address with the R/W bit set to "1", the master must first perform a "dummy" write operation. The master issues a start request, a slave address (R/W bit = "0") and then the register address to read. After the register address is acknowledged, the master immediately reissues the start request and the slave address with the R/W bit set to "1". The AK5366VR then generates an acknowledge, 1 byte of data and increments the internal address counter by 1. If the master does not generate an acknowledge to the data but instead generates a stop condition, the AK5366VR ceases transmission.
S T A R T S T A R T Sub Address(n) A C K A C K
R/W="0"
R/W="1"
S T O P Data(n) Data(n+1) A C K A C K A C K Data(n+x) A C K P
SDA
Slave S Address
Slave S Address A C K
Figure 21. RANDOM ADDRESS READ
MS0526-E-00 - 31 -
2006/07
ASAHI KASEI
[AK5366VR]
SDA
SCL S start condition P stop condition
Figure 22. START and STOP Conditions
DATA OUTPUT BY TRANSMITTER not acknowledge DATA OUTPUT BY RECEIVER acknowledge SCL FROM MASTER S clock pulse for acknowledgement
1
2
8
9
START CONDITION
Figure 23. Acknowledge on the I2C-Bus
SDA
SCL
data line stable; data valid
change of data allowed
Figure 24. Bit Transfer on the I2C-Bus
MS0526-E-00 - 32 -
2006/07
ASAHI KASEI
[AK5366VR]
Control by Pin and Bit
Function Pin SEL2-0 Pin "LLL" : LIN1/RIN1 "LLH" : LIN2/RIN2 "LHL" : LIN3/RIN3 "LHH" : LIN4/RIN4 "HLL" : LIN5/RIN5 SMUTE Pin (Internal Pull-down) "L" : Normal operation "H" : Soft muted Table 13. Pin and Bit control bit SEL2-0 bit "000" : LIN1/RIN1 "001" : LIN2/RIN2 "010" : LIN3/RIN3 "011" : LIN4/RIN4 "100" : LIN5/RIN5 SMUTE bit "0" : Normal operation "1" : Soft muted
Input Selector
Soft Mute
Note : The SEL2-0 pins should be fixed to "LLL" if the AK5366VR is controlled by the SEL2-0 bits, because the setting of the SEL2-0 pins are prior to the SEL2-0 bits setting. Soft Mute is ORed between pin and register.
Register Map
Addr 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH Register Name Power Down & Reset Control Input Selector Control Clock & Format Control Timer Select Lch IPGA Control Rch IPGA Control ALC Mode Control 1 ALC Mode Control 2 Lch DATT Control Rch DATT Control Lch Peak Hold Low Byte Lch Peak Hold High Byte Rch Peak Hold Low Byte Rch Peak Hold High Byte D7 0 0 0 0 IPGL7 IPGR7 0 REF7 ATTL7 ATTR7 PHL7 PHL15 PHR7 PHR15 D6 0 0 0 0 IPGL6 IPGR6 0 REF6 ATTL6 ATTR6 PHL6 PHL14 PHR6 PHR14 D5 0 0 0 LTM1 IPGL5 IPGR5 ZELMN REF5 ATTL5 ATTR5 PHL5 PHL13 PHR5 PHR13 D4 0 0 0 LTM0 IPGL4 IPGR4 ALC REF4 ATTL7 ATTR4 PHL4 PHL12 PHR4 PHR12 D3 0 0 DIF ZTM1 IPGL3 IPGR3 FR REF3 ATTL7 ATTR3 PHL3 PHL11 PHR3 PHR11 D2 MCKPD SEL2 CKS1 ZTM0 IPGL2 IPGR2 LMTH REF2 ATTL7 ATTR2 PHL2 PHL10 PHR2 PHR10 D1 MCKAC SEL1 CKS0 WTM1 IPGL1 IPGR1 RATT REF1 ATTL7 ATTR1 PHL1 PHL9 PHR1 PHR9 D0 PWN SEL0 SMUTE WTM0 IPGL0 IPGR0 LMAT REF0 ATTL0 ATTR0 PHL0 PHL8 PHR0 PHR8
PDN pin = "L" resets the registers to their default values. Note: Unused bits must contain a "0" value. Note: Only write to address 00H to 09H. Note: 3-wire serial control does not support Read function. I2C control supports Read function.
MS0526-E-00 - 33 -
2006/07
ASAHI KASEI
[AK5366VR]
Register Definitions
Addr 00H Register Name Power Down & Reset Control R/W Default D7 0 RD 0 D6 0 RD 0 D5 0 RD 0 D4 0 RD 0 D3 0 RD 0 D2 MCKPD R/W 0 D1 MCKAC R/W 0 D0 PWN R/W 1
PWN: Power down control 0 : Power down. All registers are not initialized. 1 : Normal Operation (Default) "0" powers down all sections and then both IPGA and ADC do not operate. The contents of all register are not initialized and enabled to write to the registers. When MCLK and LRCK are changed, it is not necessary to reset by the PDN pin or PWN bit because the AK5366VR builds in reset-free circuit. However, it can be reduced the noise by reset. MCKAC: Master Clock input Mode Select 0 : CMOS input (Default) 1 : AC coupling input MCKPD: MCLK Input Buffer Control 0 : Enable (Default) 1 : Disable When MCLK input with AC coupling is stopped, MCKPD bit should be set to "1".
Addr 01H
Register Name Input Selector Control R/W Default
D7 0 RD 0
D6 0 RD 0
D5 0 RD 0
D4 0 RD 0
D3 0 RD 0
D2 SEL2 R/W 0
D1 SEL1 R/W 0
D0 SEL0 R/W 0
SEL2-0:
Input selector (see Table 6) Initial values are "000".
Addr 02H
Register Name Clock & Format Control R/W Default
D7 0 RD 0
D6 0 RD 0
D5 0 RD 0
D4 0 RD 0
D3 DIF R/W 0
D2 CKS1 R/W 0
D1 CKS0 R/W 0
D0 SMUTE R/W 0
SMUTE: Soft Mute control 0 : Normal Operation (Default) 1 : SDTO outputs soft-muted. CKS1-0: Master clock frequency select (see Table 2) Initial values are "00". DIF: Audio interface format (see Table 4) Initial values are "0" (24bit, MSB first).
MS0526-E-00 - 34 -
2006/07
ASAHI KASEI
[AK5366VR]
Addr 03H
Register Name Timer Select R/W Default
D7 0 RD 0
D6 0 RD 0
D5 LTM1 R/W 1
D4 LTM0 R/W 0
D3 ZTM1 R/W 1
D2 ZTM0 R/W 0
D1 WTM1 R/W 1
D0 WTM0 R/W 1
WTM1-0: ALC Recovery waiting time (see Table 14) A period of recovery operation when any limiter operation does not occur during the ALC operation. WTM1 0 0 1 1 WTM0 0 1 0 1 ALC recovery operation waiting period 288/fs 1152/fs 2304/fs 4608/fs Table 14. ALC recovery waiting time @fs=48kHz 6ms 24ms 48ms 96ms
Default
ZTM1-0: Zero crossing timeout (see Table 15) When the IPGA of each L/R channels perform zero crossing or timeout independently, the IPGA value is changed by the P WRITE operation, ALC recovery operation or ALC limiter operation (ZELMN bit = "0"). ZTM1 0 0 1 1 ZTM0 0 1 0 1 Zero crossing timeout period @fs=48kHz 288/fs 6ms 1152/fs 24ms 2304/fs 48ms 4608/fs 96ms Table 15. Zero crossing timeout
Default
LTM1-0: ALC Limiter period (see Table 16) When ZELMN bit = "1", the IPGA value is changed immediately. When the IPGA value is changed continuously, the change is done by the period set by the LTM1-0 bits. LTM1 0 0 1 1 LTM0 0 1 0 1 ALC limiter operation period 3/fs 6/fs 12/fs 24/fs Table 16. ALC limiter period @fs=48kHz 63s 125s Default 250s 500s
MS0526-E-00 - 35 -
2006/07
ASAHI KASEI
[AK5366VR]
Addr 04H 05H
Register Name Lch IPGA Control Rch IPGA Control R/W Default
D7 IPGL7 IPGR7 R/W 1
D6 IPGL6 IPGR6 R/W 0
D5 IPGL5 IPGR5 R/W 0
D4 IPGL4 IPGR4 R/W 0
D3 IPGL3 IPGR3 R/W 0
D2 IPGL2 IPGR2 R/W 0
D1 IPGL1 IPGR1 R/W 0
D0 IPGL0 IPGR0 R/W 0
IPGL/R7-0: Input PGA & Digital volume control (see Table 17) Initial values are "80H". The data must not be written under 80H. Writing to the area over 7FH (Table 17) of IPGL/R registers (04H, 05H) is ignored during ALC operation. After ALC is disabled, the IPGA changes to the last written data by zero-crossing or time-out. In case of writing to the DATT area (Table 11) of DATT registers (08H, 09H), the DATT changes even if ALC is enabled. Data (hex) A4H : 9EH : 98H 97H 96H : 82H 81H 80H Gain (dB) +18 : +15 : +12 +11.5 +11 : +1.0 +0.5 0 Step width (dB) 0.5 0.5 0.5 0.5 IPGA 0.5 0.5 Analog volume with 0.5dB step 0.5 0.5 0.5 0.5 Table 17. IPGA Code Table
MS0526-E-00 - 36 -
2006/07
ASAHI KASEI
[AK5366VR]
Addr 06H
Register Name ALC Mode Control 1 R/W Default
D7 0 RD 0
D6 0 RD 0
D5 ZELMN R/W 1
D4 ALC R/W 0
D3 FR R/W 1
D2 LMTH R/W 0
D1 RATT R/W 0
D0 LMAT R/W 0
LMAT: ALC Limiter ATT step (see Table 18) During the ALC limiter operation, when either Lch or Rch exceeds the ALC limiter detection level set by LMTH bit, the number of steps attenuated from the current IPGA value is set. For example, when the current IPGA value is 94H and the LMAT bit = "1", the IPGA transition to 92H when the ALC limiter operation starts, resulting in the input signal level being attenuated by 1dB (=0.5dB x 2). LMAT ATT Step 0 1 Default 1 2 Table 18. ALC limiter ATT step RATT: ALC Recovery gain step (see Table 19) During the ALC recovery operation, the number of steps changed from the current IPGA value is set. For example, when the current IPGA value is 82H and RATT bit = "1" is set, the IPGA changes to 84H by the ALC recovery operation and the output signal level is gained up by 1dB (=0.5dB x 2). When the IPGA value exceeds the reference level (REF7-0 bits), the IPGA value does not increase. RATT Gain Step 0 1 Default 1 2 Table 19. ALC recovery gain step LMTH: ALC Limiter detection level / Recovery waiting counter reset level (see Table 20) The ALC limiter detection level and the ALC recovery counter reset level may be offset by about 2dB. LMTH 0 1 ALC Limiter Detection Level ALC Recovery Waiting Counter Reset Level ALC Output -0.5dBFS -0.5dBFS > ALC Output -2.5dBFS ALC Output -2.0dBFS -2.0dBFS > ALC Output -4.0dBFS Table 20. ALC Limiter detection level / Recovery waiting counter reset level
Default
FR: ALC fast recovery 0 : Disable 1 : Enable (Default) When the impulse noise is input, the ALC recovery operation becomes faster than a normal recovery operation. ALC: ALC enable flag 0 : ALC Disable (Default) 1 : ALC Enable
ZELMN: Zero crossing enable flag at ALC limiter operation 0 : Enable 1 : Disable (Default) When the ZELMN bit = "0", the IPGA of each L/R channel perform a zero crossing or timeout independently. The zero crossing timeout is the same as the ALC recovery operation. When the ZELMN bit = "1", the IPGA value is changed immediately. The ALC Limiter period can be set up by a ZTM 1-0 bits when ZELMN bit = "0", it can be set up by a LTM1-0 bits when ZELMN bit = "1"
MS0526-E-00 - 37 -
2006/07
ASAHI KASEI
[AK5366VR]
Addr 07H
Register Name ALC Mode Control 2 R/W Default
D7 REF7 R/W 1
D6 REF6 R/W 0
D5 REF5 R/W 0
D4 REF4 R/W 0
D3 REF3 R/W 1
D2 REF2 R/W 1
D1 REF1 R/W 1
D0 REF0 R/W 0
REF7-0: Reference value at ALC recovery operation (see Table 21) During the ALC recovery operation, if the IPGA value exceeds the setting reference value by gain operation, then the IPGA does not become larger than the reference value. The REF7-0 bits should not be set up except for Table 21. DATA (hex) Gain (dB) A4H +18.0 : : 90H +8.0 8FH +7.5 8EH +7.0 Default 8DH +6.5 : : 89H +4.5 : : 81H +0.5 80H 0 Table 21. Reference value at ALC recovery operation
Addr 08H 09H
Register Name Lch DATT Control Rch DATT Control R/W Default
D7 ATTL7 ATTR7 R/W 0
D6 ATTL6 ATTR6 R/W 1
D5 ATTL5 ATTR5 R/W 1
D4 ATTL4 ATTR4 R/W 1
D3 ATTL3 ATTR3 R/W 1
D2 ATTL2 ATTR2 R/W 1
D1 ATTL1 ATTR1 R/W 1
D0 ATTL0 ATTR0 R/W 1
ATTL/R7-0: Digital output volume control (see Table 11) Initial value is "7FH". The data must not be written over 90H. When PDN pin = "L", ATTL/R7-0 bits are initialized "7FH". When PWN bit = "0", the DATT holds the last setting value.
Addr 0AH 0BH 0CH 0DH
Register Name Lch Peak Hold Low Byte Lch Peak Hold High Byte Rch Peak Hold Low Byte Rch Peak Hold High Byte R/W Default
D7 PHL7 PHL15 PHR7 PHR15 0
D6 PHL6 PHL14 PHR6 PHR14 0
D5 PHL5 PHL13 PHR5 PHR13 0
D4 PHL4 PHL12 PHR4 PHR12 RD 0
D3 PHL3 PHL11 PHR3 PHR11 0
D2 PHL2 PHL10 PHR2 PHR10 0
D1 PHL1 PHL9 PHR1 PHR9 0
D0 PHL0 PHL8 PHR0 PHR8 0
PHL15-0: Lch Peak Hold Low/High Byte PHR15-0: Rch Peak Hold Low/High Byte The AK5366VR includes the peak hold circuit. The peak is held L/R audio data independently. These registers are reset by reading 8bit of MSB, reading 8bit of both MSB and LSB should be continuity controlled by reading in order of 8bit of MSB from LSB. After reading 8bit of LSB the last, 8bit of MSB is lost by reading 8bit of LSB the last. The output value is the absolute value. Full scale is "FFFFH". These registers are reset by PDN pin = "L" or PWN bit = "0".
MS0526-E-00 - 38 -
2006/07
ASAHI KASEI
[AK5366VR]
SYSTEM DESIGN
Figure 25 shows the system connection diagram. An evaluation board is available which demonstrates application circuits, the optimum layout, power supply arrangements and measurement results. * Master Mode, 3-wire control (I2C pin = "L")
1 47k 48 RIN5
1 47k 47 TEST8 46 RIN4
1 47k 45 TEST7 44 RIN3
1 47k 43 TEST6 42 RIN2
1 47k 41 TEST5 40 RIN1 39 NC 38 M/S 37 I2C CSN/CAD1 36 CCLK/SCL 35 CDTI/SDA 34 SEL2 33 SEL1 32
1
47k 1 LIN5 2 TEST1
1
47k 3 LIN4 4 TEST2
1
47k 5 LIN3 6 TEST3
1
47k 7 LIN2 8 TEST4
Top View
SEL0 31 SMUTE 30 TVDD 29 PDN 28 MCLK 27 LRCK 26 0.1 Reset
DSP and uP
1
47k 9 LIN1 10 NC 11 LOPIN ROPIN IPGAR VCOM IPGAL ROUT DVDD 23 AVDD AVSS 12 LOUT 4.7 DVSS
24k
BICK 25 SDTO 24 10 NC 18
13
14
NC
15
16
17 24k
19
20
21
22
4.7
0.1 0.1 10 2.2
0.1 10
Analog Supply 4.75 ~ 5.25V
Digital Supply 3.0 ~ 5.25V
Note: - AVSS and DVSS of the AK5366VR should be distributed separately from the ground of external digital devices (MPU, DSP etc.). - When LOUT/ROUT drives a capacitive load, resistors should be added in series between LOUT/ROUT and capacitive load. - All digital input pins should not be left floating. - M/S pin should be connected to AVDD or AVSS. Figure 25. Typical Connection Diagram
MS0526-E-00 - 39 -
2006/07
ASAHI KASEI
[AK5366VR]
1. Grounding and Power Supply Decoupling The AK5366VR requires careful attention to power supply and grounding arrangements. AVDD, DVDD and TVDD are usually supplied from the analog supply in the system. Alternatively if AVDD, DVDD and TVDD are supplied separately, the power up sequence is not critical. AVSS and DVSS of the AK5366VR must be connected to analog ground plane. System analog ground and digital ground should be connected together near to where the supplies are brought onto the printed circuit board. Decoupling capacitors should be as near to the AK5366VR as possible, with the small value ceramic capacitor being the closest. 2. Voltage Reference Inputs The differential voltage between AVDD and AVSS sets the analog input range. VCOM is a signal ground of this chip. An electrolytic capacitor 2.2F parallel with a 0.1F ceramic capacitor attached to VCOM pin eliminates the effects of high frequency noise. No load current may be drawn from the VCOM pin. All signals, especially clocks, should be kept away from the VREF and VCOM pins in order to avoid unwanted coupling into the AK5366VR. 3. Analog Inputs An analog input of AK5366VR is single-ended input to Pre-Amp through the external resistor. For input signal range, adjust feedback resistor so that Pre-Amp output may become the input range (typ. 0.2 x AVDD Vrms) of IPGA (IPGAL, IPGAR pin). Between the Pre-Amp output (LOUT, ROUT pin) and the IPGA input (IPGAL, IPGAR pin) is AC coupled with capacitor. When the impedance of IPGAL/R pins is "R" and the capacitor of between the Pre-Amp output and the IPGA input is "C", the cut-off frequency is fc = 1/(2RC). The ADC output data format 2's compliment. The internal HPF removes the DC offset. The AK5366VR samples the analog inputs at 64fs. The digital filter rejects noise above the stop band except for multiples of 64fs. The AK5366VR includes an anti-aliasing filter (RC filter) to attenuate a noise around 64fs. 4. Attention to the PCB Wiring LIN1-5 and RIN1-5 pins are the summing nodes of the Pre-Amp. Attention should be given to avoid coupling with other signals on those nodes. This can be accomplished by making the wire length of the input resistors as short as possible. The same theory also applies to the LOPIN/ROPIN pins and feedback resistors; keep the wire length to a minimum. Unused input pins among LIN1-5 and RIN1-5 pins should be left open. When external devices are connected to LOUT and ROUT pin, the input impedance of an external device which the LOUT and ROUT pins can drive is min 6.3k.
MS0526-E-00 - 40 -
2006/07
ASAHI KASEI
[AK5366VR]
PACKAGE
48pin LQFP(Unit:mm)
9.0 0.2 7.0 36 37 25
1.70Max 0.13 0.13
1.40 0.05 24 9.0 0.2
48 1 0.22 0.08 12
13
7.0
0.16 0.07 0.5 0.10 M
0 10
0.10
0.5 0.2
Material & Lead finish
Package molding compound: Lead frame material: Lead frame surface treatment: Epoxy Cu Solder (Pb free) plate
MS0526-E-00 - 41 -
2006/07
ASAHI KASEI
[AK5366VR]
MARKING
AK5366VR XXXXXXX
1
XXXXXXX : Date Code Identifier (7 digits) Date (YY/MM/DD) 06/07/20 Revision 00 Reason First edition Page Contents
IMPORTANT NOTICE * These products and their specifications are subject to change without notice. Before considering any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized distributor concerning their current status. * AKM assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein. * Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. * AKM products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and AKM assumes no responsibility relating to any such use, except with the express written consent of the Representative Director of AKM. As used here: a. A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. b. A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. * It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification.
MS0526-E-00 - 42 -
2006/07

▲Up To Search▲

Price & Availability of AK5366VR

	To Download AK5366VR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .